- 525
- 产品价格：面议
- 发货地址：河北衡水枣强县 包装说明：按要求包装
- 产品数量：345654.00 平米产品规格：规格齐全，可定制
- 信息编号：91217607公司编号：14468070
- 徐经理 微信 139328197..
- 进入店铺 在线咨询 QQ咨询 在线询价
营口玻璃钢除雾器 脱硫塔除雾器全新报价
- 相关产品：
营口玻璃钢除雾器
“打造行业优质产品，满足客户的专业需求”，枣强县荣驰玻璃钢有限公司供应的玻璃钢除雾器支持银行转账；在线支付等付款方式，一旦您付款，我们将会在双方协商的时间发货（运费：买卖双方协商）。玻璃钢除雾器**国内玻璃钢市场。由我公司自主生产的玻璃钢除雾器是经玻璃钢行业*鉴定后评定为优质的产品，**业界。我们坚持公司内部建立的任何组织，流程，制度都必须建立在为客户提供更优质的服务的基础上，为了让客户能够快速的收到货物，我们采取的是陆运；公路运输的物流方式进行配送，在全国拥有众多客户。
订购电话： Q
订购电话： Q
营口玻璃钢除雾器冲洗周期
冲洗周期是指除雾器每次冲洗的时间间隔。由于除雾器冲洗期间导致烟气带水量加大所以冲洗不宜过于频繁，但也不要间隔太长，否则易产生结垢现象，除雾器的冲洗周期主要根据烟气特征及吸收剂确定，一般以不**过2h为宜，也就是不冲洗为冲洗时间的3~6倍；循环单道时间在20-60秒之间。
冲洗周期是指除雾器每次冲洗的时间间隔。由于除雾器冲洗期间导致烟气带水量加大所以冲洗不宜过于频繁，但也不要间隔太长，否则易产生结垢现象，除雾器的冲洗周期主要根据烟气特征及吸收剂确定，一般以不**过2h为宜，也就是不冲洗为冲洗时间的3~6倍；循环单道时间在20-60秒之间。
营口玻璃钢除雾器冲洗水管选型技术要求
1、除雾器机械要求
1.1除雾器冲洗水管能够满足正常工作的压力要求，保证正常的使用寿命。
1.2除雾器冲洗水管能够满足吸收塔内的使用工况，包括微酸性气体环境，以及含部分颗粒物的烟气。
1.3除雾器冲洗管、喷嘴及构件应能在吸收塔腐蚀、热和磨损浆液条件下防止断裂和腐蚀。管道应易于拆卸和组合。
1.4供方应确保烟气温度在80摄氏度时和短时(10分钟)90摄氏度除雾器冲洗水管不会损坏。
1.5喷嘴设计应与管道连接牢固并易于拆卸。除雾器喷嘴与管道应长期牢固地运行在实际活荷载下。
1.6所有组件的设计，包括除雾器冲洗水母管、支管及和喷嘴的链接构件应有足够的强度，能够承受除雾器重新水泵的压力，并能防止实际运行条件下的振动。
2、除雾器材料要求
2.1除雾器管道、法兰采用玻璃钢FRP，喷嘴采用PP-R材质。
2.2垫圈采用EPDM。
2.3所有法兰采用HG20592标准。
2.4除雾器材料性能完全满足使用工况要求。
1、除雾器机械要求
1.1除雾器冲洗水管能够满足正常工作的压力要求，保证正常的使用寿命。
1.2除雾器冲洗水管能够满足吸收塔内的使用工况，包括微酸性气体环境，以及含部分颗粒物的烟气。
1.3除雾器冲洗管、喷嘴及构件应能在吸收塔腐蚀、热和磨损浆液条件下防止断裂和腐蚀。管道应易于拆卸和组合。
1.4供方应确保烟气温度在80摄氏度时和短时(10分钟)90摄氏度除雾器冲洗水管不会损坏。
1.5喷嘴设计应与管道连接牢固并易于拆卸。除雾器喷嘴与管道应长期牢固地运行在实际活荷载下。
1.6所有组件的设计，包括除雾器冲洗水母管、支管及和喷嘴的链接构件应有足够的强度，能够承受除雾器重新水泵的压力，并能防止实际运行条件下的振动。
2、除雾器材料要求
2.1除雾器管道、法兰采用玻璃钢FRP，喷嘴采用PP-R材质。
2.2垫圈采用EPDM。
2.3所有法兰采用HG20592标准。
2.4除雾器材料性能完全满足使用工况要求。
Principle of FRP mist eliminator
When the gas is flowing through the demister at a certain speed, the droplets are separated from the surface of the wave plate when the droplets are bumped with the wave plate and the droplets are larger than those of the gas, due to the inertia impact of the gas.
The multiple folding structure of the FRP mist eliminator increases the opportunity to collect the droplets, and the non removed mist is arrested at the next corner through the same function, so that the efficiency of the mist removal is greatly improved.
After passing through the corrugated board mist eliminator, the gas is basically foggy. The flue gas is separated from the liquid droplets in the air flow under the action of the inertia force and gravity through the bending channel of the demister. The flue gas after the desulphurization is flowing through the demister at a certain speed. The smoke is quickly and continuously changes the direction of movement. The fog droplets in the flue gas impact the foggy mist eliminator blade because of the effect of centrifugal force and inertia. The fog drops gather to form water and fall into the slurry pool because of gravity. The gas and liquid separation is realized, which makes the fume through the mist eliminator discharge after the mist removal.
Consulting Hotline: Q
When the gas is flowing through the demister at a certain speed, the droplets are separated from the surface of the wave plate when the droplets are bumped with the wave plate and the droplets are larger than those of the gas, due to the inertia impact of the gas.
The multiple folding structure of the FRP mist eliminator increases the opportunity to collect the droplets, and the non removed mist is arrested at the next corner through the same function, so that the efficiency of the mist removal is greatly improved.
After passing through the corrugated board mist eliminator, the gas is basically foggy. The flue gas is separated from the liquid droplets in the air flow under the action of the inertia force and gravity through the bending channel of the demister. The flue gas after the desulphurization is flowing through the demister at a certain speed. The smoke is quickly and continuously changes the direction of movement. The fog droplets in the flue gas impact the foggy mist eliminator blade because of the effect of centrifugal force and inertia. The fog drops gather to form water and fall into the slurry pool because of gravity. The gas and liquid separation is realized, which makes the fume through the mist eliminator discharge after the mist removal.
Consulting Hotline: Q
联系电话是13932819705, 主要经营模压化粪池 、玻璃钢桥架、除雾器。
单位注册资金单位注册资金人民币 100 - 250 万元。
